550℃ Glass Frit Powder

550℃ Glass Frit Powder

550°C glass frit powder — a genuinely low temperature glass frit that flows and seals at 530–570°C, so decoration, sealing and coating can be fired onto substrates that would not survive a conventional cycle. Lead-free options, decal-ready fineness, and a published trade-off table instead of vague claims.
Send Inquiry
Description

Product Overview

 

This is a glass frit whose working temperature sits around 550°C - roughly 250°C below a conventional ceramic glaze and 100–200°C below standard glass enamels. Fired in the 530–570°C window, the powder softens, wets and seals without thermally loading the substrate beneath it, which is exactly what makes a low temperature glass frit 550C useful: decal firing on glassware, decoration over an existing fired surface, enamelling on temperature-sensitive metals, sealing and thick-film applications, and any process where the kiln's temperature is the binding constraint. Supplied lead-free, in decal-grade and coating-grade fineness, with the durability trade-off of each grade stated on its sheet.

 

Why 550 Is a Different Product, Not a Discount Version

A frit that flows at 550°C is made by loading the glass with strong fluxes - boron, bismuth, alkali - and keeping silica low. That has consequences, and honest suppliers name them:

What you gain. A substrate that cannot take 800°C becomes usable. A second firing can sit on top of a first decoration without disturbing it. A kiln run at 550°C consumes materially less energy than the same run at 800°C, heats faster, cools faster, and puts less thermal stress on ware, setters and elements. Energy saving glass frit powder is not a slogan here - it is the arithmetic of a lower setpoint.

What you trade. Low-temperature glasses are, as a family, less chemically durable than high-silica glasses. Alkali-rich compositions are more sensitive to dishwasher detergents, acids and long weathering. Our answer is not to hide it: each grade carries a durability rating, and the glass frit for sensitive substrates grade is formulated for the applications where the fired film is protected or interior, not for continuously washed ware.

Energy saving glass frit powder

 

Three Applications Where This Frit Earns Its Place

Decal firing.

Ceramic and glass decals need a flux that softens under the pigment without dissolving it, and burns out the organic vehicle completely before the glass seals. Our decal firing glass frit grades are milled fine (D50 in the single-digit micron range) and matched to a burnout schedule: slow ramp through 300–450°C to clear the vehicle, then the 550°C soak. Skip the slow ramp and the carbon stays in the film - that grey haze on a "failed" decal is usually unburned vehicle, not bad frit.

Sensitive substrates.

Already-fired glazes, thin glass, temperature-sensitive metals: the constraint is not what the coating can take, but what the part can. Here the frit is chosen for the lowest flow that still seals, with CTE matched so the coating stays in compression rather than cracking on cooling.

Sealing and bonding.

Where two glass or ceramic surfaces must join below the softening point of either, a 550°C frit is the joining medium - provided the CTE match and the crystallization behaviour are controlled, so the seal does not reflow or devitrify in service.

 

The Lead-Free Question, Answered Straight

 

Low-temperature flow was historically easy with lead, and that is why so much decal and enamel chemistry was built on it. Our lead-free low temperature glass frit grades reach the same window with bismuth- and alkali-boron systems. The difference is not invisible: bismuth grades hold durability better but cost more; alkali grades are cheaper but need the durability rating respected. We publish which system each grade uses, so the choice is yours to make with data rather than a datasheet adjective.

 


Products Description

 

Grade

Answers the question

Key parameter

Low temperature glass frit 550C (platform)

"The standard 550°C sealing/coating frit?"

Fires 530–570°C, 10 min soak

Decal firing glass frit

"Flux for decal inks and transfers?"

D50 3–8 µm, clean burnout schedule

Glass frit for sensitive substrates

"Lowest thermal load on the part?"

Lowest flow grade, tight CTE match

Lead-free low temperature glass frit

"No lead, still 550°C?"

Bi- or alkali-boron systems, durability rated

Energy saving glass frit powder

"Fast cycles, lower setpoint?"

Short-soak variant, 530–550°C

 

Technical Data (typical - replace with your lab's certificate values)

 

Property

Typical value

Method

Firing range

530–570°C, 10 min soak

Fired-button assessment

Glass transition (Tg)

~400–440°C

DSC / dilatometer

Softening point

~470–510°C

Dilatometer, hot stage

CTE, 100–300°C (COE)

7.0–9.0 × 10⁻⁶/K, matched to soda-lime glass and common glaze substrates

Dilatometer

Particle size

Decal grades D50 3–8 µm; coating grades 200–325 mesh

Laser diffraction

LOI

≤ 0.5%

550°C ignition loss

Durability rating

Stated per grade (acid, detergent, weathering)

Acid immersion / mass loss

 
How We Test It - the Evidence Behind the Claims
 

"550" is measured, not printed.

Every batch is verified on the hot stage and by fired-button test at 550°C for 10 minutes - a batch that needs 580 to flow is not sold as this grade.

Tg and softening by DSC/dilatometer per batch

because at this temperature window, a 20°C shift changes whether the film seals or stays matt.

Burnout verification for decal grades

fired films checked for residual carbon under magnification before the grade is released; the burnout schedule on the sheet is the one that produced a clean film in our furnace.

Adhesion and durability testing

cross-hatch and tape test, boiling-water immersion, thermal cycling on matched substrates.

CTE per batch

since at 550°C the film is thin and the substrate does the mechanical work - expansion mismatch shows up as crazing within days, not years.

COA with every batch

chemistry, Tg, softening, CTE, particle size.

Sample Request

 

Tell us the substrate (glass, fired glaze, metal), the maximum temperature it can take, and what the film must survive afterwards (handling, washing, weathering). We will return a fired coupon on a matching substrate with its DSC curve and durability rating - for decal work, include your ink system so the burnout schedule matches.

 

Lead-free low temperature glass frit

 

 
FAQ
 
01/

Can it be fired onto ordinary soda-lime glassware? Yes, with two conditions: CTE matched to the substrate (this is the main reason decorated glass cracks on cooling) and a controlled cooling ramp. The grade sheet states the match window; tell us your glass and we confirm before shipping.

02/

Is the lead-free version as durable as leaded frit? Close, not identical - bismuth grades come nearest, alkali grades trade some detergent resistance for cost. Each grade carries a durability rating so you can decide against your actual service conditions rather than a marketing claim.

03/

Why does my decal come out grey or hazy? Almost always incomplete organic burnout. At 550°C the glass seals quickly; if the vehicle has not cleared by then, carbon is trapped in the film. Slow the ramp through 300–450°C and hold before the soak - the schedule ships with the grade.

04/

Can it fire over an existing decoration? That is one of its main uses - the 550°C setpoint is low enough that a previously fired decoration underneath is not disturbed. Test on your own ware: the lower decoration's own thermal history matters.

Call to Action

 

The value of a 550°C frit is not that it is low - it is that it makes a substrate, a decoration or a cycle possible that was not. Send us the substrate and its temperature ceiling, request a fired coupon with its DSC curve, and see whether 550 is the number your process has been missing.

 

Contact Glaze Peak (Zibo Glaze Peak New Materials Technology Co., Ltd.) for samples, grade sheets, or a firing-window review of your current low-temperature process.

Hot Tags: 550℃ glass frit powder, China 550℃ glass frit powder manufacturers, suppliers, factory, lead bisilicate frit, Lead Frit, lead frit for artistic glaze, Lead silicate frit, low lead frit, specialty frits

Send Inquiry
Send Inquiry