Borosilicate Glass Frit

Borosilicate Glass Frit

Borosilicate glass frit — a lead-free, low expansion glass frit engineered so that thermal shock becomes arithmetic instead of luck. Built on the same glass chemistry as laboratory glassware, it gives ovenware, glass cookware and acid-resistant coatings a surface that shrugs off temperature jumps other glazes crack on.
Send Inquiry
Description

Product Overview

Borosilicate glass frit is a high-silica glass in which boron oxide (B₂O₃) acts as part of the glass network itself, dropping thermal expansion to levels ordinary glaze glasses cannot reach. It is the frit family behind ovenware glaze frit, coatings for glass cookware, acid-resistant enamels, and any surface where the defining requirement is thermal shock resistance. Supplied as melt-verified borosilicate frit powder in milling grades from 80 to 325 mesh, it is lead-free by composition - not by substitution - and every batch ships with a dilatometer-measured CTE on its certificate.

Thermal Shock Is Arithmetic

Heat resistant glass frit

When a hot surface cools faster than the body beneath it, the mismatch generates tensile stress - and the stress scales directly with the glass coefficient of expansion. Lower the expansion, and the same temperature jump that cracks a soda-lime surface becomes survivable.

That is the whole product in one sentence: borosilicate frit sells a number. A soda-lime glaze glass expands at roughly 8–9 × 10⁻⁶/K; the low expansion glass frit grades in this family sit between 3.2 and 4.2 × 10⁻⁶/K, and body-matched grades for ceramic ovenware at 4.5–5.5. In freezer-to-oven service, that difference is not cosmetic - it is the margin between the surface surviving the cycle and growing hairline cracks that food soil and detergent will find.

Boron earns this by its position in the glass: B₂O₃ enters the network as a former, not as a flux sitting between network units, and the resulting borosilicate structure combines low expansion with working softening points low enough to fire.

 

 

Why Melting It Separates Suppliers

 

The chemistry that delivers low expansion also makes the melt difficult - and this is where furnace discipline becomes part of the product.

Borosilicate melts run hot and viscous. Under-melted batches leave unmelted silica grains, and every one of them is a latent flaw: a hard inclusion in the fired surface, a polishing fault on cookware, a crack initiator under thermal cycling. At melt temperature, boron is also volatile - leave the furnace window uncontrolled and the batch that leaves the furnace is not the batch that entered it.

 

Both problems answer to the same control: melt temperature held in a narrow band, and B₂O₃ verified by XRF on every batch against the input charge. A COA from us reports the boron that actually arrived in the frit, not the boron the recipe promised. That single line of data is what "batch-to-batch consistency" means when the product is thermal expansion.

 

What the Buyer Gets

 

  • Service survival: ware that goes freezer → oven → sink without crazing, for retail brands where one cracked casserole is a bad review.
  • Lead-free by design: no lead was ever in the system to remove - compliance conversations get shorter (see lead-free borosilicate frit).
  • Chemical durability: the same borosilicate family that laboratory glassware is made of - laboratory glass frit grades carry strong acid resistance for lab ceramic ware and acid-resistant coatings.
  • Substrate matching, not guessing: two expansion windows so the frit is matched to the body, because a perfect glass with the wrong expansion is still a cracked glaze.

 

Grade Selection

Grade

Answers the question

Key parameter

Thermal shock resistant frit (platform)

"Which one do I start with?"

CTE 3.2–4.2 × 10⁻⁶/K, general ovenware service

Low expansion glass frit

"Minimum expansion for extreme cycling?"

CTE 3.2–3.6 × 10⁻⁶/K

Frit for glass cookware

"Coating directly on borosilicate substrates?"

Expansion matched to the substrate (~3.3 × 10⁻⁶/K)

Ovenware glaze frit

"Glaze on ceramic ovenware bodies?"

CTE 4.5–5.5 × 10⁻⁶/K, set below the body for mild compression

Laboratory glass frit / acid-resistant grades

"Chemical attack resistance first?"

Acid durability prioritized alongside low expansion

 

Technical Data (typical - replace with your lab's certificate values)

 

Property

Typical value

Method

SiO₂

70–78 wt%

XRF / wet chemistry

B₂O₃

10–15 wt%, verified per batch against melt charge

XRF

CTE, 100–600°C (COE)

3.2–4.2 (low-expansion grades); 4.5–5.5 (body-matched grades)

Dilatometer, per batch

Softening point

~780–830°C

Dilatometer / hot-stage

Firing window (enamel-on-steel / powder coat)

780–860°C sinter

Fired-button assessment

Firing window (ceramic glaze use)

1150–1250°C

Fired-plate trials

Particle size

80–325 mesh, per application

Laser diffraction

Lead content

None by composition

XRF screening

Acid durability

High - borosilicate family

Acid immersion, mass-loss method

 

How We Test It - the Evidence Behind the Claims

 

CTE per batch: every production batch measured on the dilatometer, held to a tight internal tolerance band around the grade target - the certificate line is the measured value, not the datasheet value.

Thermal shock cycling: fired coupons quenched through repeated ΔT cycles (hot-air-to-water) at increasing severity until failure; the grade's pass threshold, not just "tested", goes on the grade sheet.

Boron verification: XRF B₂O₃ per batch against the melt charge - the number that proves the furnace discipline.

Acid/alkali immersion for laboratory and coating grades.

Melt behaviour: button-flow test per batch to catch under-melting before it becomes a fired flaw.

modular-1

 

Sample Request

 

Tell us the substrate - borosilicate glass, ceramic ovenware body, or steel - and the firing conditions it allows. We will return a fired coupon on your substrate with the dilatometer curve and the grade sheet. For expansion-matched applications, a coupon is the only honest sample: powder cannot demonstrate what this frit is for.

 

 

FAQ
 
 

Q1. Why are there two expansion windows?

+

-

Because expansion only matters relative to the substrate. A glaze on a ceramic ovenware body needs to sit slightly below the body's expansion; a coating on borosilicate glass cookware needs to match ~3.3 × 10⁻⁶/K. One number cannot serve both - matching is the product, not an option.

Q2. Is "lead-free" a substitution or a claim?

+

-

Neither - lead was never part of the borosilicate system. The compliance story is structural, which is why it holds across every grade without reformulation.

Q3. Why does boron content need batch verification?

+

-

Boron is volatile at melt temperature. An uncontrolled furnace slowly changes the batch chemistry - and with it the expansion, which is the one property this frit cannot drift on. XRF per batch is how the CTE on the certificate stays the CTE in the fired ware.

Q4. Can it be used as a powder coating on steel?

+

-

Yes - the powder grades are designed for sinter-firing in the 780–860°C window. Tell us the steel grade and line speed so we confirm the sinter window against your process.

Q5. How thermal-shock resistant is "resistant"?

+

-

The grade sheet carries a quench-cycle threshold - the ΔT severity the fired coupon survives. We publish the number and the method so your QC can repeat it; ask for the grade sheet with your sample.

Call to Action

 

Low expansion is not a slogan you can see on a fired tile - so we put it in writing instead. Send us your substrate and firing window, request a fired coupon with its dilatometer curve, and hold us to the number on the certificate.

 

Contact Glaze Peak (Zibo Glaze Peak New Materials Technology Co., Ltd.) for samples, grade sheets, or a substrate-matching review of your current ovenware or cookware coating.

Hot Tags: borosilicate glass frit, China borosilicate glass frit manufacturers, suppliers, factory, bone china glaze material, glaze fit adjustment frit, high b2o3 frit, high translucency frit, low temperature boron frit, transparent frit for bone china

Send Inquiry
Send Inquiry